ppm-series ? ppm20-e-xxelf ? single output - plasti c case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 1/3 ppm20-e-xxelf all specifications typical at ta=25c, nominal inpu t voltage and full load unless otherwise specified input specifications input voltage range 85 ? 264 vac or 120 ? 370 vdc universal input frequency 47 ? 440 hz 110 vac 230 vac input (inrush) current 370 ma (20a), typ. 240ma (40a), typ. external input fuse (recommended) 3.15a / 250v slow blow output specifications voltage accuracy 2%, typ (3% at 3.3 vout) input variation 0.5%, typ load variation (10-100%) 1% , typ ripple and noise (20mhz bandwidth) 120mv pk-pk, max short circuit protection continuous, auto resume over current protection > 110% io, auto resume common specifications temperature range -40c to +70 c power derating 2.5% / c (above 40c) case temperature +95c (max) storage -40c to +105 c hold up time 50ms, typ. (230vac) humidity (non condensing) 95%, max. temperature coefficient 0.02%/c switching frequency 100khz, typ i/o isolation voltage 3000vac / 1min. leakage current 0.75ma, (max at vin 240vac) emi / rfi conducted en55022, level b emc compliance esd en 55024/iec/en 61000-4-2 level 4 8kv/15kv rf en55024/iec/en 61000-4-3 level 4 10v/m eft / bursts en55024/iec/en 61000-4-4 level 4 4kv surge en55024/iec/en 61000-4-5 level 4 2kv/4kv safety standards iec60950, en60950, ul60950 safety approvals en60950, ul60950 (pending) safety class class 2 case material ul94v-0 rated reliability calculated mtbf (mil-hdbk-217f) > 300,000 hrs weight ~ 50g mainzer stra?e 151?153 d-55299 nackenheim tel. +49 6135 7026-0 fax: +49 6135 931070 www.peak-electronics.de peak@peak-electronics.de the ppm - series are high efficiency green power m oduls with various packaging provided by peak. the features of this se ries are: wide input voltage, dc and ac all in one, high efficiency, hig h reliability, low loss, safety isolation etc. they are widely used in indus trial, office and civil equipments. ppm-series 20 watt univ. 85-264vac (120-370vdc) single output over voltage protection (out) 3 kv ac i/o isolation low ripple and noise high efficiency rev.04-2012
ppm-series ? ppm20-e-xxelf ? single output - plasti c case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 2/3 selection guide single output order # p o w e r ( w ) o u t p u t v o l t a g e ( v d c ) o u t p u t c u r r e n t f u l l l o a d ( m a ) e f f i c i e n c y ( % ) single output PPM20-E-3R3ELF 11.8 3.3 3600 74 ppm20-e-05elf 18 5 3600 78 ppm20-e-12elf 20 12 1660 82 ppm20-e-15elf 20 15 1330 83 ppm20-e-24elf 20 24 833 83 if you need other specifications, please enquire. package / pinning / derating all dimensions are typical in millimeters (inches). - pin diameter: 1.0 +/-0.10 (0.04 +/-0.004) - pin pitch tolerance: +/-0.35 (+/-0.014) - case tolerance +/-0.5 (+/-0.02) specification may change without notice. modelcode datecode 23.50 (0.93) 2" x 1" C plastic case 2 4 1 3 45.72 (1.80) 6.00 (0.24) pe a k 53.50 (2.10) bottom view # single 1 ac (n) 2 ac (l) 3 + vout 4 - vout pin connections
ppm-series ? ppm20-e-xxelf ? single output - plasti c case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 3/3 app notes: measure typical applications ppm-series external typical value model c1 c2 tvs PPM20-E-3R3ELF 220f/10v 0.1f/50v p6ke6.8a ppm20-e-05elf 220f/10v 0.1f/50v p6ke6.8a ppm20-e-12elf 120f/25v 0.1f/50v p6ke20a ppm20-e-15elf 120f/25v 0.1f/50v p6ke20a ppm20-e-24elf 68f/25v 0.1f/50v p6ke30a note 1. output filtering capacitors c1 is electrolytic c apacitors. it is recommended to use high frequency and low impedance electrolytic capacitors. for capacitance and current of capacitor, please refer to manufactu re?s datasheet. voltage derating of capacitor should be 80% or above. c2 is ceramic capacitor - it is used to filter high frequency noise. tvs is a recommended c omponent to protect post-circuits (if converter fai ls). 2. external connect fuse, recommended the parameter is 3.15a/250v slow blow.
|
